Summary: 80 instances, 74 unique

Text	Count
/* FIXME: init w3220 registers here */	1
/* TODO: Use CP8 if possible... */	1
/* FIXME: enable LCDC here */	1
* TODO: Add your own basebaord init function and call it from	1
int SW7 = 0;  /* FIXME: get from SCR (Mst doc section 3.2.1.1) */	1
* FIXME: this is reimplementing I2C bit-bangining. Move this	1
* FIXME: Remove remaining definitions	1
/* TODO: DMACH_XD0 */	1
/* FIXME: put optimal value here. Current one is just estimation */	1
dev_warn(dev, "%s: FIXME: missing hwmod/omap_dev info\n", __func__);	2
* FIXME dm6441 (no MMC/SD), dm357 (one), and dm335 (two) are	1
* FIXME: this should probably depend on which system state we're	1
* FIXME: Find a mechanism to enable/disable runtime the McBSP ICLK autoidle.	1
/* FIXME: non-speculating: flush on bidirectional mappings? */	1
* FIXME: This is terrible and needs to be nuked. The notifier is used	1
/* TODO: select external clock/oscillator */	1
/* FIXME: Enabling interrupts here is racy! */	1
/* TODO: put this 'table' into ts78xx-fpga.h */	1
* TODO: Get additional info (where applicable)	1
* TODO: Switch this pin from dedicated usage to GPIO if	1
/** TODO - check that this is after the cmdline option! */	1
/* FIXME: use egpio when implemented */	1
* FIXME: we don't follow this 100% yet.	1
/* TODO: DMACH_XD1 */	1
/* FIXME: non-speculating: not required */	1
/* TODO: cleanup soc_is_* */	1
* FIXME: The test here is not sufficient to detect if the	1
/* FIXME define and use a boot tag; not all boards will be hooking	1
/* FIXME: this is not correct */	1
* FIXME: 9th bit, of Auxillary Controller register must be set	1
* FIXME: shouldn't do this here.	1
* FIXME: Add support to set_smp_affinity() once the core	1
/* TODO: Handle mode and cmd if necessary */	1
* TODO: Access flag faults introduced in ARMv6K.	1
* FIXME: Should we set up the GPIO domain here?	1
/* TODO Check backup volt multiplier */	1
/* FIXME: This should return a proper error code ! */	1
* FIXME: This clock seems to be necessary but no-one has asked for its	3
/* TODO: switch on/off uart in powersave mode */	1
/* FIXME */	2
* FIXME: this is needed to communicate between the pinctrl driver and	1
MACHINE_START(SMDK2410, "SMDK2410") /* @TODO: request a new identifier and switch	1
* FIXME: This should be moved to dsp code	1
/* TODO: DMACH_TIMER */	1
/* TODO:	1
* FIXME: This is a copy of IMX_IO_P2V in hardware.h, and needs to	1
/* TODO: Adjust timings??? */	1
* FIXME: This function should be called before entering off-mode after	1
/* FIXME: Shared IRQs on COM1-COM4 will not work properly on v1i1 hardware. */	1
* Step 1: turn off interrupts (FIXME: NOTE: already disabled)	1
* TODO: handle ARMv6K properly. Runtime check for 'K' extension is	1
* TODO: Check write support on flash MX29LV400CBTC-70G	1
/* FIXME: notify irq controller to standard enable FIQs */	1
* FIXME: this just sets the two pins as non-opendrain, as no	1
* FIXME behaves like (6,3), may differ for host/device	1
/* FIXME: should this have |GPIO_OPEN_DRAIN set? */	1
/* Copied from imx6: TODO factorize */	1
* FIXME: Make remaining drivers use dynamic mapping.	1
* FIXME: needs this MCRR to be supported.	1
// FIXME omap_cfg_reg(USB2_SPEED);	1
/* FIXME setpower */	1
/* FIXME: not highmem safe */	2
* FIXME: the timer needs some delay to stablize the counter capture	1
/* FIXME:  PCMD_SQC need be checked.   */	1
.name = "led1:green",    /* FIXME */	1
* TODO: ifdef out some instruction decoding based on architecture.	1
/* TODO when driver support is ready:	2
* in this mapping of the page.  FIXME: this is overkill	1
* FIXME: we currently manage device-specific idle states	1
/* FIXME: Remove this when MPU OSWR support is added */	1
* FIXME correct answer depends on hmc_mode,	1
* FIXME revC boards (and H3) support NAND-boot, with a dip switch to	1
.name = "led0:red",    /* FIXME */	1
/* FIXME behaves like (4,1), may differ for host/device */	1