static int bluecard_open()

in bluecard_cs.c [680:790]

• 66 lines of code
• 7 McCabe index (conditional complexity)

static int bluecard_open(struct bluecard_info *info)
{
	unsigned int iobase = info->p_dev->resource[0]->start;
	struct hci_dev *hdev;
	unsigned char id;

	spin_lock_init(&(info->lock));

	timer_setup(&info->timer, bluecard_activity_led_timeout, 0);

	skb_queue_head_init(&(info->txq));

	info->rx_state = RECV_WAIT_PACKET_TYPE;
	info->rx_count = 0;
	info->rx_skb = NULL;

	/* Initialize HCI device */
	hdev = hci_alloc_dev();
	if (!hdev) {
		BT_ERR("Can't allocate HCI device");
		return -ENOMEM;
	}

	info->hdev = hdev;

	hdev->bus = HCI_PCCARD;
	hci_set_drvdata(hdev, info);
	SET_HCIDEV_DEV(hdev, &info->p_dev->dev);

	hdev->open  = bluecard_hci_open;
	hdev->close = bluecard_hci_close;
	hdev->flush = bluecard_hci_flush;
	hdev->send  = bluecard_hci_send_frame;

	id = inb(iobase + 0x30);

	if ((id & 0x0f) == 0x02)
		set_bit(CARD_HAS_PCCARD_ID, &(info->hw_state));

	if (id & 0x10)
		set_bit(CARD_HAS_POWER_LED, &(info->hw_state));

	if (id & 0x20)
		set_bit(CARD_HAS_ACTIVITY_LED, &(info->hw_state));

	/* Reset card */
	info->ctrl_reg = REG_CONTROL_BT_RESET | REG_CONTROL_CARD_RESET;
	outb(info->ctrl_reg, iobase + REG_CONTROL);

	/* Turn FPGA off */
	outb(0x80, iobase + 0x30);

	/* Wait some time */
	msleep(10);

	/* Turn FPGA on */
	outb(0x00, iobase + 0x30);

	/* Activate card */
	info->ctrl_reg = REG_CONTROL_BT_ON | REG_CONTROL_BT_RES_PU;
	outb(info->ctrl_reg, iobase + REG_CONTROL);

	/* Enable interrupt */
	outb(0xff, iobase + REG_INTERRUPT);
	info->ctrl_reg |= REG_CONTROL_INTERRUPT;
	outb(info->ctrl_reg, iobase + REG_CONTROL);

	if ((id & 0x0f) == 0x03) {
		/* Disable RTS */
		info->ctrl_reg |= REG_CONTROL_RTS;
		outb(info->ctrl_reg, iobase + REG_CONTROL);

		/* Set baud rate */
		info->ctrl_reg |= 0x03;
		outb(info->ctrl_reg, iobase + REG_CONTROL);

		/* Enable RTS */
		info->ctrl_reg &= ~REG_CONTROL_RTS;
		outb(info->ctrl_reg, iobase + REG_CONTROL);

		set_bit(XMIT_BUF_ONE_READY, &(info->tx_state));
		set_bit(XMIT_BUF_TWO_READY, &(info->tx_state));
		set_bit(XMIT_SENDING_READY, &(info->tx_state));
	}

	/* Start the RX buffers */
	outb(REG_COMMAND_RX_BUF_ONE, iobase + REG_COMMAND);
	outb(REG_COMMAND_RX_BUF_TWO, iobase + REG_COMMAND);

	/* Signal that the hardware is ready */
	set_bit(CARD_READY, &(info->hw_state));

	/* Drop TX queue */
	skb_queue_purge(&(info->txq));

	/* Control the point at which RTS is enabled */
	outb((0x0f << RTS_LEVEL_SHIFT_BITS) | 1, iobase + REG_RX_CONTROL);

	/* Timeout before it is safe to send the first HCI packet */
	msleep(1250);

	/* Register HCI device */
	if (hci_register_dev(hdev) < 0) {
		BT_ERR("Can't register HCI device");
		info->hdev = NULL;
		hci_free_dev(hdev);
		return -ENODEV;
	}

	return 0;
}